On this page down the page you can locate a good deal of worthwhile insight involving How to Install a Bathtub.
Setting up a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult task. If the old bathtub is conveniently obtainable, the project can relocate immediately; if you need to open a wall to get rid of the old bathtub and position the brand-new tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration using one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This post will aid you set up a new tub in your restroom if you have actually currently bought a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools and material list should consist of the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the regular electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub needs to wait until the bath tub has been utilized at least once as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the tap and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split a stiff seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in issues with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that article about A Step-by-Step Guide to Installing a Bathtub when doing a search on the web. Sharing is nice. You just don't know, you might be doing someone a favor. I praise you for your time. Visit us again soon.
Click Here To Read More